Back 2 Lay the Late Mover Guardian Automation Bot

Post Reply
User avatar
Dallas
Posts: 22674
Joined: Sun Aug 09, 2015 10:57 pm
Location: Working From Home

tootatoota wrote:
Tue Apr 28, 2020 5:40 am
Dallas,
As i understand it you would need all 3 triggers before the bet is placed?
Also what would happen if after the back bet is placed say at 2.0 and the 1.61 lay did not get matched in the run?
How do you get out if you have to?
Can there be another rule added to it ?
Thanks Brendan
Its upto the user to add any exit stratergy they want if the offset isn't matched/doen't look like it will be matched.
You can add as many other rules to this or any other example as you want
User avatar
tootatoota
Posts: 56
Joined: Fri Apr 17, 2020 2:33 am

Thanks Dallas
Is there a condition where it voids bets under a certain number of starters?
I have had a look a cannot see one
Regards Brendan
User avatar
Dallas
Posts: 22674
Joined: Sun Aug 09, 2015 10:57 pm
Location: Working From Home

tootatoota wrote:
Wed Apr 29, 2020 7:37 am
Thanks Dallas
Is there a condition where it voids bets under a certain number of starters?
I have had a look a cannot see one
Regards Brendan
You can't have a bet voided once matched unless BF do it
User avatar
tootatoota
Posts: 56
Joined: Fri Apr 17, 2020 2:33 am

Sorry you misunderstood.
Is there a condition that will trigger if there is say 7 starters or less?
So my rule is working fine but i have been losing on races under 6 or 7 starters.
So i would like to not bet in that race.
i have a rule that says the automation doesnt start until over 5k in volume of bets.
i would also like it to say automation doesnt start due to insufficient starters?
Thanks Brendan
User avatar
ShaunWhite
Posts: 9731
Joined: Sat Sep 03, 2016 3:42 am

tootatoota wrote:
Wed Apr 29, 2020 11:35 pm
i would also like it to say automation doesnt start due to insufficient starters?
https://www.betangel.com/user-guide/con ... 3D&mw=MzIw#
Screenshot_2.png
You do not have the required permissions to view the files attached to this post.
User avatar
tootatoota
Posts: 56
Joined: Fri Apr 17, 2020 2:33 am

Thanks shaun i thought that related to somethingelse
smd100
Posts: 18
Joined: Sun May 21, 2017 9:51 pm

Hi guys, in the original automation file the signal sets when the price reduces by 5%.

I would like to know if the signal can be reset if the price were to reverse back above that 3.35 theshold (and can be activated again, should it go below 3.35)

I was looking at the clear signal command but don't know how to make it work as above (if at all it does)

Many thanks
User avatar
Dallas
Posts: 22674
Joined: Sun Aug 09, 2015 10:57 pm
Location: Working From Home

smd100 wrote:
Fri May 01, 2020 6:26 am
Hi guys, in the original automation file the signal sets when the price reduces by 5%.

I would like to know if the signal can be reset if the price were to reverse back above that 3.35 theshold (and can be activated again, should it go below 3.35)

I was looking at the clear signal command but don't know how to make it work as above (if at all it does)

Many thanks
Yes, first you'll need to add a Stored Value of the price to the first rule

Then you'll need a new 'Set/Modify Stored Value rule' and on the SV tab reset the Stored value named (the orginal SV)
This rule will need the following condition
Stored Value Condition
Is the price greater
Than Another Stored Value (enter the SV you've just added to the first rule)
Post Reply

Return to “Bet Angel Automation - Horse racing - In-running”