Signal when Goals are Scored Guardian Automation Bot
Ok can you post a screenshot of the general tab of the new signal rule as we know that's not triggering at the moment
There should be no conditions on that rule just the signal being set on the tab
No image came through, but yes those conditions are checking for a goal, so they don't need to be used with this rule
and they'll be stopping it triggering
Hi Dallas, sorry to bug you, but on this new signal, how many times should it trigger, just once?Dallas wrote: ↑Tue Sep 14, 2021 11:05 amTo do this add another 'Set/Modify Signal' rule, and give it the same signal name (but different value ie, 99)Mitch567 wrote: ↑Tue Sep 14, 2021 6:48 amHowdy, just wondering if there is a way of storing the time value of when these signals are created and then using that time value to trigger a greening up. So for example, if I wanted to Lay the Over X Goals and Green Up either after 15 minutes if no goal scored (That bit of automation I have sorted), but if a goal has been scored in the first 15 minutes, delay the greening up until 15 minutes after the last goal.
So, if a team scored after 8 minutes, it would green up after 23 minutes unless a goal was scored in the 21st minute, when it would green up in the 36th minute and so on..
Any help much appreciated.
and arm this to trigger 30secs after the match has gone in-play
Then on your green up rule add a signal changed condition
and test the signal named XXXXX
changed between 900 and 1020 secs ago
If no goals are scored that condition will allow the green up to trigger 15mins after that first signal was set
If there is a goal and another signal value is set it'll be 15 mins after that
Yes, the signal rule just needs to trigger the one timeMitch567 wrote: ↑Wed Sep 15, 2021 8:30 amHi Dallas, sorry to bug you, but on this new signal, how many times should it trigger, just once?Dallas wrote: ↑Tue Sep 14, 2021 11:05 amTo do this add another 'Set/Modify Signal' rule, and give it the same signal name (but different value ie, 99)Mitch567 wrote: ↑Tue Sep 14, 2021 6:48 amHowdy, just wondering if there is a way of storing the time value of when these signals are created and then using that time value to trigger a greening up. So for example, if I wanted to Lay the Over X Goals and Green Up either after 15 minutes if no goal scored (That bit of automation I have sorted), but if a goal has been scored in the first 15 minutes, delay the greening up until 15 minutes after the last goal.
So, if a team scored after 8 minutes, it would green up after 23 minutes unless a goal was scored in the 21st minute, when it would green up in the 36th minute and so on..
Any help much appreciated.
and arm this to trigger 30secs after the match has gone in-play
Then on your green up rule add a signal changed condition
and test the signal named XXXXX
changed between 900 and 1020 secs ago
If no goals are scored that condition will allow the green up to trigger 15mins after that first signal was set
If there is a goal and another signal value is set it'll be 15 mins after that
How many ticks would you suggest if using this on 3.5 or 4.5 goals?Dallas wrote: ↑Wed Aug 24, 2016 6:11 pmSignal Goals O-U 2.5
This works slightly different to the above rule as you will see, its for use on the over/under 2.5 markets and just as the above file does it looks for a 10+ tick movement of the odds from the overs during the first half and 60secs after a market was last unsuspended again in most cases this means a goal has been scored. It now sets a signal with a value of 1 to highlight this, the signal value is increased by one each time ANY team then scores so the current value of the signal will tell you the likely number of goals in the match so far and therefore you can then trigger your own automation rules based on this information.
For example
Team B scores a signal is set – Goal 1
Team A scores the signal is now changed to – Goal 2
Team A scores again signal is now changed to – Goal 3
Here if you have an existing Over/Under rule or strategy that is based on number of goals, then a condition can be added to this current rule which looks for a signal value before being allowed to trigger.
You might want to back the under 2.5 if there has been a 2nd goal in the 1st half, this would be done by adding a ‘signal value condition’ is ‘equal’ to goal 2 to your back rule (see image below).
Or you may want to lay the over 2.5 if an early goal is scored here on your lay rule the condition would be ‘Signal Value condition’ is ‘equal’ to 1.
Just the same as the other 'Signal Goals' file from the post above there is also endless possibilities on ways this one can be used on either the O/U 2.5 markets or any other Over/Under markets.
If you wish to use it on other over/under markets 0.5,3.5 & 4.5 etc) it will just require the number of ticks editing before setting any signal similar to the earlier rule.
-
- Posts: 1
- Joined: Wed Apr 29, 2020 12:06 pm
Hi team, new to the automation caper and attempting to kick off a strategy along the lines of..
Back over 1.5g in play once odds exceed a certain level (say $1.48 for this example)
After a goal has been scored, green-up my position
I've used the 'signal goal' file originally shared and added the back condition - so far no issue getting the back bet to automatically place in-play. The problem I'm having is getting the green up condition to trigger after the goal has been scored. In fact the 'signal' never triggers when I look at the 'automation' or 'log' headers back in the Guardian view.
Attaching what I've got thus far - any help greatly appreciated.
Back over 1.5g in play once odds exceed a certain level (say $1.48 for this example)
After a goal has been scored, green-up my position
I've used the 'signal goal' file originally shared and added the back condition - so far no issue getting the back bet to automatically place in-play. The problem I'm having is getting the green up condition to trigger after the goal has been scored. In fact the 'signal' never triggers when I look at the 'automation' or 'log' headers back in the Guardian view.
Attaching what I've got thus far - any help greatly appreciated.
You do not have the required permissions to view the files attached to this post.
Those signal rules where made for the match odds market as they monitor and trigger on row 3Seanwester wrote: ↑Thu Jan 20, 2022 2:32 pmHi team, new to the automation caper and attempting to kick off a strategy along the lines of..
Back over 1.5g in play once odds exceed a certain level (say $1.48 for this example)
After a goal has been scored, green-up my position
I've used the 'signal goal' file originally shared and added the back condition - so far no issue getting the back bet to automatically place in-play. The problem I'm having is getting the green up condition to trigger after the goal has been scored. In fact the 'signal' never triggers when I look at the 'automation' or 'log' headers back in the Guardian view.
Attaching what I've got thus far - any help greatly appreciated.
The OP contains another signal file which was made for the O/U markets, it would be easier to use that rather than edit this one